Inaccurate water tests – or did I do something wrong after all?

In the aquarium scene we often hear people talking about “accurate” and “inaccurate” tests. But mostly they mean a rougher or finer scaling of the output values. If a test is inaccurate this is mostly because of an application error when dosing the reagents and the amounts of water, or because of the way the test was used. Unintendedly inaccurate readings also often cause errors which result in this statement.

The test works accurately as long as a water test has not expired its best-before date and the application instructions are followed. But remember: once a water test has been opened, it starts to age. That’s why tests should be used 9 – 12 months after the initial opening at the latest. After this period some deviation in the measurement accuracy can occur. The best-before date is only valid for the unopened product.

Often minor problems can have a major impact. In case of problems our customer service will gladly help you. In the following we have listed and described the most frequent application errors for the water test types “drop test” and “test strips”. If you avoid these errors your next measurement will be even more precise.

Typical errors when using the drop tests

  • Contaminated glass cuvettes: Residues from the last measurement or of tap water can strongly affect the measurement. The glass cuvettes need to be thoroughly cleaned and dried after each water test. Rinse the glass before every test with the water to be tested.
  • Partial droplets of reagents: Everyone knows what it is like to have drops filled with air bubbles. Hold the reagent bottle vertically over the glass cuvette and carefully press the bottle. That’s how you avoid air pockets, which reduce the amount of reagent for the test reaction, thus falsifying the result. In practice many testers discard the first drop since this is often filled with air.
  • What spoon end? Heaped or level? Some water tests require the addition of powder. This always means level, NOT heaped spoons. For some tests you use the small, less noticiable, end of the spoon. If too much powder is added for either reason, the result will be inaccurate.
  • Reading errors caused by not using the comparator block: The ambient light has a big influence on the reading accuracy of the test results. To reduce light from entering laterally and enable you to read the results as precisely as possible, the enclosed comparator block needs to be used. The blank test compensates for the intrinsic colour of the water which can mislead your reading. Ensure there is sufficient daylight and avoid strong artificial lighting. Compare the measuring result of a test without a comparator block in a dark room and in the open air. You will be astonished.
  • Service life of test: If the test has passed its best-before date or it has been open longer than 9 – 12 months this can lead to a deviation in test results. If you receive colours which can’t be found in the colour chart this is the most frequent cause. You will find the best-before date on the back of each test case and on the packaging of the individual tests. Please also make a note of the date of the first opening. If none of these factors apply, one of the intended reagents was probably wrongly dosed or mixed up.
  • Waiting times: almost every test has allowed waiting times which should suffice until the reading of the end result. Some tests also require waiting times between the adding of individual reagents. Should these waiting times not be upheld, the measured values will be incorrect.
  • The water quantities are important: always use the enclosed syringe to dose the correct water quantity. Dosing into the vessels by eye will lead to incorrect results since the round form of the container means the surface tension of the water optically bends the water and deceives our eyes.
  • Colour weakness: This primarily affects men and they are often not aware of it. Colour weakness but also red-green colour blindness can be differently pronounced and make reading of some tests difficult. Undetected, this could influence the interpretation of the results. If you are unsure a second person should be consulted as a check.

Typical errors when using test strips

  • Removing excessive water: After dipping the strip into the water there is a lot of excessive water in the individual test fields – sometimes even small water domes. To remove the water the test strip needs to be laterally tapped on a liquid absorbent underlay. Please do NOT shake the strip in the air because through this the measuring fields might react with each other and the water will not be sufficiently removed. This is the most frequent cause of measuring errors and reading problems. If two fields react with each other, these are not evenly changing colours. Position: Always hold the smartphone vertically over the ColorCard. If you hold it at an angle of 45 ° over the ColorCard this will result in distortions.
  • Age of the test strips: The test strip reacts with the contact to water. The more often the package has been opened the more humidity enters into the small tube. If after a measurement the tube has not been closed, the test strips inside may react to the humidity and not deliver correct measuring values anymore.
  • Light and reflections: Sufficient daylight is required for readings. Excessive water on the test strip or direct light from a lamp onto a reflecting surface can lead to lighting-based reflections and an incorrect perception of the colour. Use kitchen paper as matt, non-reflective underlay and carry out the reading in bright light, similar to daylight.
  • Uphold the waiting time: To receive correct measuring results you need to uphold a waiting time of 60 seconds. Since the test strips continue to react steadily the reading of the measuring values, following the exact prescribed time, is the most important factor for a correct measurement.
  • Colour weakness: This primarily affects men and they are often not aware of it. Colour weakness but also red-green colour blindness can be differently pronounced and make reading of some tests difficult. Undetected, this could influence the interpretation of the results. If you are unsure a second person should be consulted as a check.

Comparing values from different water tests

Every test has a fixed scaling range which enables the assignment of measurement data. The steps in a drop test here are different to the JBL PROSCAN of JBL PROAQUATEST EASY 7in1 . They don’t always have the same scaling and this can result in non-congruent measuring points leading to different measuring results than in your other tests. It is thus important to note that similar measuring results are acceptable: they don’t have to be completely identical. If, however, the values deviate substantially from each other, a faulty measurement has probably been caused by one of the above mentioned reasons.

© 22.10.2016
Matthias Wiesensee
Matthias Wiesensee
M.Sc. Wirtschaftsinformatik

Social Media, Online Marketing, Homepage, Kundenservice, Problemlöser, Fotografie, Blogger, Tauchen, Inlineskating, Aquaristik, Gartenteich, Reisen, Technik, Elektronische Musik

Over mij: Seit Teenagerzeiten mit Aquarien in Kontakt. Klassische Fischaquarien, reine Pflanzenaquarien bis hin zum Aquascape. Aber auch ein Gartenteich und Riffaquarien begleiten mich privat im Hobby. Als Wirtschaftsinformatiker, M.Sc. bin ich als Online Marketing Manager bei JBL für die Bereiche Social Media, Webentwicklung und der Kommunikation mit dem Anwender der JBL Produkte zuständig und kenne die JBL Produkte im Detail.

Reacties

Cookies, een korte info, dan gaat het verder

Ook de JBL homepage gebruikt meerdere soorten cookies om u de volledige functionaliteit te kunnen garanderen en de benodigde service te kunnen bieden: Technische en functionele cookies hebben we absoluut nodig om ervoor te zorgen dat alles soepel verloopt tijdens uw bezoek aan onze homepage. Aanvullend zetten we cookies in voor marketingdoeleinden. Zo is het zeker dat we u bij een volgend bezoek op onze omvangrijke pagina herkennen, het succes van onze campagnes kunnen beoordelen en u, aan de hand van de gepersonaliseerde cookies, individueel en direct kunnen aanspreken kunnen – overeenkomend met uw interesses – ook buiten onze homepage. U kunt op elk moment – ook later nog – vastleggen welke cookies u accepteert en welke niet (meer daarover onder “Instellingen wijzigen”).

Ook de JBL homepage gebruikt diverse soorten cookies om u de volledige functionaliteit en talrijke diensten aan te kunnen bieden: Technisch en functionele cookies hebben we nodig om uw bezoek aan deze website te laten slagen. Daarnaast gebruiken we cookies voor de marketing. U kunt op elk moment - ook later dus nog - bepalen welke cookies u wel en welke u niet wilt toestaan (meer daarvoor onder 'Instellingen aanpassen').

In onze verklaring inzake gegevensbescherming leest u hoe wij omgaan met persoonlijke gegevens en voor welke doeleinden wij de gegevensverwerking gebruiken. leest u hoe wij omgaan met persoonlijke gegevens en voor welke doeleinden wij de gegevensverwerking gebruiken. Bevestig alstublieft met 'Gelezen en begrepen' het gebruik van alle cookies en dan kunnen we verder gaan.

U bent 16 jaar of ouder? Dan bevestigt u met "Ik heb kennisgenomen" het gebruik van alle cookies - en dan gaat het verder.

Selecteer uw Cookie-instellingen

Technische en functionele Cookies, zodat tijdens uw bezoek aan onze website alles soepel verloopt.
Marketing Cookies, zodat we u op onze pagina's herkennen en het succes van onze campagnes kunnen beoordelen.

PUSH-berichten van JBL

Wat zijn PUSH-berichten nou eigenlijk? Als onderdeel van de W3C-standaard definiëren webberichten een API voor eindgebruikerberichten, die via de browserberichten aan de desktop en/of mobiele apparaten van de gebruiker worden gestuurd. Op de eindapparaten verschijnen meldingen, zoals de eindgebruiker die kent van op het apparaat geïnstalleerde apps (bijv. e-mails). Op de eindapparaten verschijnen berichten, zoals de eindgebruiker die kent van op het apparaat geïnstalleerde apps (bijv. e-mails)

Deze notificaties maken het voor een websitebeheerder mogelijk contact op te nemen met zijn gebruikers, zolang de browser van de betreffende gebruiker openstaat – ongeacht of de gebruiker op dat moment de website bezoekt of niet.

Om web push notificaties te kunnen versturen, heb je alleen een website nodig waarop een web push code geïnstalleerd is. Hierdoor kunnen ook merken zonder apps profiteren van de vele voordelen van push berichten (gepersonaliseerde real-time communicatie op precies het juiste moment).

Webberichten zijn onderdeel van de W3C standaard en definiëren een API voor de eindgebruikerberichten. Een bericht maakt het mogelijk de gebruiker buiten de context van een website over een gebeurtenis, zoals een nieuw blogbericht, te informeren.

JBL GmbH & Co. KG biedt deze service gratis aan. De service kan net zo gemakkelijk geactiveerd, als gedeactiveerd worden.