The substrate heating

Ogrzewanie podżwirowe

With a substrate heating you promote the growth of your aquatic plants enormously by creating a water circulation in the substrate, which washes nutrient-rich water directly to the roots. A substrate heating consists of a long heating cable which is laid in curved lines on the bottom panel of the aquarium. The water heats up directly at the cable and rises upwards. Cooler water starts to flow between the cable loops, creating a water circulation in the bottom area which permanently washes nutrient-rich water to the plant roots. Only very fine substrates (fine sand) might prevent a sufficient water circulation for a substrate heating. In this case heat is very likely to become trapped at the bottom, which is not ideal. That’s why undergravel heating cables are only suitable from grain sizes of around 0.8 mm onwards.

A substrate heating is not meant to heat your aquarium water, it only serves as “micro circulation” in the bottom area. Therefore the wattage of the undergravel heating cable is significantly lower than that of heaters. You can read how to install a substrate heating here: Instalacja Wyposażenie techniczne .

Which wattage is right for your aquarium?

If you look on the packaging of the substrate heating cable JBL PROTEMP b III to find out which aquarium size the heating cable is suitable for, you will see a wide range. For example, the smallest substrate heating cable, the JBL PROTEMP b10 , is marked 40-120 litres. The number of litres is actually not the decisive factor, but the area on which the substrate heating is to be laid out! That’s why it says 40-80 cm under the number of litres. In a 40 cm aquarium, the length of the substrate heating cable (e.g. 3.6 m for the 10 W version) would be sufficient for the entire substrate. In an 80 cm aquarium, the loops of the heating cable would only cover part of the bottom pane. This can actually be quite useful as lots of aquariums only have plants in the rear part! So before laying the substrate heating cable, think through where the plants will be and only lay the substrate heating cable there. Aquarists who have covered the entire front part of the aquarium with grass plants will usually have to refer to the smaller aquarium size on the range specification.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

Oszczędzanie energii

It’s fine to regulate the substrate heater and the lighting together on one timer. Since the plants do not carry out photosynthesis at night, you can reduce the nutrient transport to the plant roots at night. So a substrate heater which is not temperature-controlled can be switched off at night.

Summer

If the room temperature is very high in summer, the heater thermostat automatically switches off and no longer heats the room. It’s best to check that that’s really happening! You can check the control light of the heater or simply feel it. As already mentioned, the substrate heating cable is not temperature-controlled, so you’ll need to unplug it if the water temperature is too high and only plug it in again when the water temperature has dropped to the range you need.

What’s important when installing a substrate heating cable?

First of all, there is the timing: the installation is only possible with an empty aquarium. Try to stay calm if your pet shop salesperson decides to recommend a undergravel heating cable after you have bought your entire setup equipment from them.

BEFORE you lay the cable in loops at the bottom of your aquarium, consider which areas you will plant. You’ll only need the heating cable in these areas.

And you’ll probably intend to put a long-term plant nutrient substrate ( JBL PROFLORA AquaBasis plus ) above the heating cable. Later, when you clean the ground with a substrate cleaner (gravel cleaner: JBL PROCLEAN AQUA EX 10-35 ) and plough the substrate to suck out the dirt, you won't want to pull out the nutrient substate again or get caught in the undergravel heating cable. SO only place the heating cable and long-term nutrient substrate in the planted areas.

The undergravel heating cable consists of a cable part that does not heat up and a part that does. The "cold" cable part should end where the cable enters the substrate.. Only the part of the cable under the substrate needs to heat up. You can identify the transition from the part that remains cold to the part that heats up on the JBL undergravel heating cables ( JBL PROTEMP b III ) by the black marked part of the heating cable.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

Cookies, krótka informacja, potem będziemy kontynuować

Także strona internetowa JBL korzysta z kilku rodzajów Cookies, aby zapewnić Państwu pełną funkcjonalność i wiele usług: techniczne i funkcjonalne Cookies potrzebujemy bezwzględnie, żeby wszystko udało się podczas Państwa wizyty na tej stronie internetowej. Dodatkowo używamy Cookies do marketingu. I tak jest zapewnione, że podczas ponownej Państwa wizyty na naszej obszernej stronie rozpoznamy Państwa, będziemy mogli zmierzyć sukces naszych kampanii, oraz na podstawie spersonalizowanych Cookies będziemy mogli zwracać się do Państwa indywidualnie i bezpośrednio, w sposób dopasowany do Państwa potrzeb – także poza naszą stroną internetową. Mogą Państwo w każdej chwili – także w późniejszym terminie – określić, jakie Cookies Państwo dopuszczają a jakie nie (więcej na ten temat w „Zmiana ustawień“).

Także strona internetowa JBL korzysta z kilku rodzajów Cookies, aby zapewnić Państwu pełną funkcjonalność i wiele usług: Techniczne i funkcjonalne Cookies są potrzebne nam bezwzględnie, żeby wszystko udało się podczas Państwa wizyty na tej stronie internetowej. Dodatkowo używamy Cookies do marketingu. Mogą Państwo w każdej chwili – także w późniejszym terminie – określić, jakie Cookies Państwo dopuszczają a jakie nie (więcej na ten temat w „Zmiana ustawień“).

W naszej strefie Polityka prywatności dowiedzą się Państwo, jak przetwarzamy dane osobowe i do jakich celów wykorzystujemy przetwarzanie danych. dowiedzą się Państwo, jak przetwarzamy dane osobowe i do jakich celów wykorzystujemy przetwarzanie danych. Proszę potwierdzić za pomocą „Zapoznałam/-em się“ korzystanie ze wszystkich Cookies– i już można iść dalej.

Wiek ponad 16 lat? Proszę więc potwierdzić „Zapoznałem/am się“ odnośnie korzystania ze wszystkich Cookies– i już idziemy dalej.

Proszę wybrać swoje ustawienia Cookie

Techniczne i funkcjonalne Cookie, żeby wszystko udało się podczas Państwa wizyty na naszej stronie internetowej.
Marketingowe Cookies, abyśmy mogli rozpoznać Państwa na naszych stronach i zmierzyć sukces naszych kampanii.

Wiadomości PUSH od JBL

Jako część standardu W3C, powiadomienia Web definiują API dla powiadomień użytkowników końcowych, które są wysyłane za pośrednictwem przeglądarki na pulpit urządzeń stacjonarnych i/lub urządzeń mobilnych użytkowników. Powiadomienia pojawiają się na urządzeniach końcowych tak, jak jest to znane użytkownikowi końcowemu z aplikacji zainstalowanych na urządzeniu (np. wiadomości e-mail).

Powiadomienia te umożliwiają operatorowi witryny kontaktowanie się z jego użytkownikami tak długo, jak długo mają oni otwartą przeglądarkę - niezależnie od tego, czy użytkownik aktualnie odwiedza stronę internetową, czy nie.

Aby móc wysyłać powiadomienia web push, wystarczy tylko strona internetowa z zainstalowanym kodem web push. Tym samym także marki bez aplikacji mogą korzystać z wielu zalet powiadomień push (spersonalizowana komunikacja w czasie rzeczywistym dokładnie w odpowiednim momencie.)

Powiadomienia internetowe są częścią standardu W3C i definiują API dla powiadomień użytkowników końcowych. Powiadomienie umożliwia poinformowanie użytkownika poza kontekstem strony internetowej o wydarzeniu, jak na przykład nowy wpis na blogu.

Usługa ta jest udostępniona bezpłatnie przez firmę JBL GmbH & Co. KG, i można ją równie łatwo aktywować jak i dezaktywować.