Themeworld

The substrate heating

The heater that doesn't heat but flushes - all for the benefit of the aquarium plants

With a substrate heating you promote the growth of your aquatic plants enormously by creating a water circulation in the substrate, which washes nutrient-rich water directly to the roots. A substrate heating consists of a long heating cable which is laid in curved lines on the bottom panel of the aquarium. The water heats up directly at the cable and rises upwards. Cooler water starts to flow between the cable loops, creating a water circulation in the bottom area which permanently washes nutrient-rich water to the plant roots. Only very fine substrates (fine sand) might prevent a sufficient water circulation for a substrate heating. In this case heat is very likely to become trapped at the bottom, which is not ideal. That’s why undergravel heating cables are only suitable from grain sizes of around 0.8 mm onwards.

A substrate heating is not meant to heat your aquarium water, it only serves as “micro circulation” in the bottom area. Therefore the wattage of the undergravel heating cable is significantly lower than that of heaters. You can read how to install a substrate heating here: Installation technical items .

Which wattage is right for your aquarium?

If you look on the packaging of the substrate heating cable JBL PROTEMP b III to find out which aquarium size the heating cable is suitable for, you will see a wide range. For example, the smallest substrate heating cable, the JBL PROTEMP b10 , is marked 40-120 litres. The number of litres is actually not the decisive factor, but the area on which the substrate heating is to be laid out! That’s why it says 40-80 cm under the number of litres. In a 40 cm aquarium, the length of the substrate heating cable (e.g. 3.6 m for the 10 W version) would be sufficient for the entire substrate. In an 80 cm aquarium, the loops of the heating cable would only cover part of the bottom pane. This can actually be quite useful as lots of aquariums only have plants in the rear part! So before laying the substrate heating cable, think through where the plants will be and only lay the substrate heating cable there. Aquarists who have covered the entire front part of the aquarium with grass plants will usually have to refer to the smaller aquarium size on the range specification.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

Energy saving

It’s fine to regulate the substrate heater and the lighting together on one timer. Since the plants do not carry out photosynthesis at night, you can reduce the nutrient transport to the plant roots at night. So a substrate heater which is not temperature-controlled can be switched off at night.

Summer

If the room temperature is very high in summer, the heater thermostat automatically switches off and no longer heats the room. It’s best to check that that’s really happening! You can check the control light of the heater or simply feel it. As already mentioned, the substrate heating cable is not temperature-controlled, so you’ll need to unplug it if the water temperature is too high and only plug it in again when the water temperature has dropped to the range you need.

What’s important when installing a substrate heating cable?

First of all, there is the timing: the installation is only possible with an empty aquarium. Try to stay calm if your pet shop salesperson decides to recommend a undergravel heating cable after you have bought your entire setup equipment from them.

BEFORE you lay the cable in loops at the bottom of your aquarium, consider which areas you will plant. You’ll only need the heating cable in these areas.

And you’ll probably intend to put a long-term plant nutrient substrate ( JBL PROFLORA AquaBasis plus ) above the heating cable. Later, when you clean the ground with a substrate cleaner (gravel cleaner: JBL PROCLEAN AQUA EX 10-35 ) and plough the substrate to suck out the dirt, you won't want to pull out the nutrient substate again or get caught in the undergravel heating cable. SO only place the heating cable and long-term nutrient substrate in the planted areas.

The undergravel heating cable consists of a cable part that does not heat up and a part that does. The "cold" cable part should end where the cable enters the substrate.. Only the part of the cable under the substrate needs to heat up. You can identify the transition from the part that remains cold to the part that heats up on the JBL undergravel heating cables ( JBL PROTEMP b III ) by the black marked part of the heating cable.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

A word about cookies before we continue

The JBL Homepage also uses several types of cookies to provide you with full functionality and many services: We require technical and functional cookies to ensure that everything works when you visit this website. We also use cookies for marketing purposes. This ensures that we recognise you when you visit our extensive site again, that we can measure the success of our campaigns and that the personalisation cookies allow us to address you individually and directly, adapted to your needs - even outside our website. You can determine at any time - even at a later date - which cookies you allow and which you do not allow (more on this under "Change settings").

The JBL website uses several types of cookies to provide you with full functionality and many services: Technical and functional cookies are absolutely necessary so that everything works when you visit this website. In addition, we use cookies for marketing purposes. You can determine at any time - even at a later date - which cookies you allow and which you do not (more on this under "Change settings").

Our data protection declaration tells you how we process personal data and what purposes we use the data processing for. tells you how we process personal data and what purposes we use the data processing for. Please confirm the use of all cookies by clicking "Accept" - and you're on your way.

Are you over 16 years old? Then confirm the use of all cookies with "Noticed" and you are ready to go.

Choose your cookie settings

Technical and functional cookies, so that everything works when you visit our website.
Marketing cookies, so that we recognize you on our pages and can measure the success of our campaigns.
I accept the YouTube Terms of Service and confirm that I have read and understood the YouTube Terms of Service .

PUSH messages from JBL

What are PUSH messages? As part of the W3C standard, web notifications define an API for end-user notifications that are sent to the user's desktop and/or mobile devices via the browser. Notifications appear on the end devices as they are familiar to the end user from apps installed on the device (e.g. emails). Notifications appear on the end user’s device, just like an app (e.g. for emails) installed on the device.

These notifications enable a website operator to contact its users whenever they have a browser open - it doesn’t matter whether the user is currently visiting the website or not.

To be able to send web push notifications, all you need is a website with a web push code installed. This allows brands without apps to take advantage of many of the benefits of push notifications (personalised real-time communications at just the right moment).

Web notifications are part of the W3C standard and define an API for end user notifications. A notification makes it possible to inform the user about an event, such as a new blog post, outside the context of a website.

JBL GmbH & Co. KG provides this service free of charge, and it is easy to activate or deactivate.