Bilgi Dünyası

Kum altı ısıtma

Kum altı ısıtıcı ile bitki köklerine besinler ulaştırılır

Bir kum altı ısıtıcıyla suda zengin bitkilerin büyümesini, kum altında bir su sirkülasyonu yaratarak, besin açısından zengin suyu doğrudan köklere yıkayarak yükseltirsiniz. Bir kum altı ısıtıcı, akvaryumun alt panelindeki eğri çizgiler halinde döşenmiş uzun bir ısıtma kablosundan oluşur. Su doğrudan kabloda ısınır ve yukarı doğru yükselir. Soğutucu su, kablo halkaları arasında akmaya başlar, alt kısımda besin açısından zengin suyu bitki köklerine kalıcı olarak yıkayan bir su sirkülasyonu yaratır. Sadece çok ince alt tabakalar (ince kum) alt tabaka ısıtma için yeterli su sirkülasyonunu önleyebilir. Bu durumda, sıcaklık istenmeyen bir şekilde altta sıkışabilir. Bu nedenle kum altı ısıtma kablolarının yalnızca yaklaşık 0,8 mm'lik granül boyutlarına uygun olması gerekir.

Bir kum altı ısıtıcı akvaryum suyunuzu ısıtmanız anlamına gelmez, sadece alt alanda “mikro sirkülasyon” yaratma görevi görür. Bu nedenle, yerden ısıtma kablosunun gücü, ısıtıcılardan önemli ölçüde düşüktür. Burada bir kum altı ısıtmasının nasıl kurulduğunu okuyabilirsiniz: Kurulum tekniği .

Which wattage is right for your aquarium?

If you look on the packaging of the substrate heating cable JBL PROTEMP b III to find out which aquarium size the heating cable is suitable for, you will see a wide range. For example, the smallest substrate heating cable, the JBL PROTEMP b10 , is marked 40-120 litres. The number of litres is actually not the decisive factor, but the area on which the substrate heating is to be laid out! That’s why it says 40-80 cm under the number of litres. In a 40 cm aquarium, the length of the substrate heating cable (e.g. 3.6 m for the 10 W version) would be sufficient for the entire substrate. In an 80 cm aquarium, the loops of the heating cable would only cover part of the bottom pane. This can actually be quite useful as lots of aquariums only have plants in the rear part! So before laying the substrate heating cable, think through where the plants will be and only lay the substrate heating cable there. Aquarists who have covered the entire front part of the aquarium with grass plants will usually have to refer to the smaller aquarium size on the range specification.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

Energy saving

It’s fine to regulate the substrate heater and the lighting together on one timer. Since the plants do not carry out photosynthesis at night, you can reduce the nutrient transport to the plant roots at night. So a substrate heater which is not temperature-controlled can be switched off at night.

Summer

If the room temperature is very high in summer, the heater thermostat automatically switches off and no longer heats the room. It’s best to check that that’s really happening! You can check the control light of the heater or simply feel it. As already mentioned, the substrate heating cable is not temperature-controlled, so you’ll need to unplug it if the water temperature is too high and only plug it in again when the water temperature has dropped to the range you need.

What’s important when installing a substrate heating cable?

First of all, there is the timing: the installation is only possible with an empty aquarium. Try to stay calm if your pet shop salesperson decides to recommend a undergravel heating cable after you have bought your entire setup equipment from them.

BEFORE you lay the cable in loops at the bottom of your aquarium, consider which areas you will plant. You’ll only need the heating cable in these areas.

And you’ll probably intend to put a long-term plant nutrient substrate ( JBL PROFLORA AquaBasis plus ) above the heating cable. Later, when you clean the ground with a substrate cleaner (gravel cleaner: JBL PROCLEAN AQUA EX 10-35 ) and plough the substrate to suck out the dirt, you won't want to pull out the nutrient substate again or get caught in the undergravel heating cable. SO only place the heating cable and long-term nutrient substrate in the planted areas.

The undergravel heating cable consists of a cable part that does not heat up and a part that does. The "cold" cable part should end where the cable enters the substrate.. Only the part of the cable under the substrate needs to heat up. You can identify the transition from the part that remains cold to the part that heats up on the JBL undergravel heating cables ( JBL PROTEMP b III ) by the black marked part of the heating cable.

It’s perfectly normal for the wattage of the substrate heater to be much lower than the wattage of your heater thermostat. The heater thermostat (e.g. JBL PROTEMP S 25 ) is designed to bring the water temperature of your aquarium to the correct value for your fish species, e.g. 25 °C. The substrate heating cable, on the other hand, is only intended to heat the water right at the cable so that the heated water rises and creates water circulation in the substrate. Very little energy (watts) is needed to create this water circulation.

Devam etmeden önce çerezler hakkında kısa bir bilgi notu

JBL Ana Sayfası, size tam işlevsellik ve birçok hizmet sunmak için çeşitli çerez türleri de kullanır: Bu web sitesini ziyaret ettiğinizde her şeyin çalışmasını sağlamak için teknik ve işlevsel çerezlere ihtiyacımız vardır. Çerezleri pazarlama amacıyla da kullanıyoruz. Bu, kapsamlı sitemizi tekrar ziyaret ettiğinizde sizi tanımamızı, kampanyalarımızın başarısını ölçebilmemizi ve kişiselleştirme çerezlerinin size, web sitemizin dışında bile, ihtiyaçlarınıza göre uyarlanmış, bireysel ve doğrudan hitap etmemize izin vermesini sağlar. Hangi çerezlere izin verdiğinizi ve hangilerine izin vermediğinizi istediğiniz zaman (daha sonraki bir tarihte bile) belirleyebilirsiniz (bununla ilgili daha fazla bilgiyi "Ayarları değiştir" bölümünde bulabilirsiniz).

Size tam bir işlevsellik ve bir çok hizmet sunabilmek için JBL’nin ana sayfasında da birçok çerezden yararlanılmaktadır. Bu ana sayfayı ziyaret ettiğinizde başarılı sonuçlar elde edilebilmesi için teknik ve işlevsel çerezlere kesinlikle ihtiyacımız bulunuyor. Çerezleri ayrıca pazarlama amaçlı olarak da kullanmaktayız. Hangi çerezlere izin vereceğinize, hangilerini engelleyeceğinize istediğiniz zaman -daha sonraki bir zamanda da- karar verebilirsiniz (bununla ilgili daha fazla bilgi için bakınız "Ayarları değiştir" menüsü).

Veri korunması ile ilgili beyanımızda kişisel verileri nasıl işlediğimizi ve işlediğimiz verileri hangi amaçla kullandığımızı görebilirsiniz. kişisel verileri nasıl işlediğimizi ve işlediğimiz verileri hangi amaçla kullandığımızı görebilirsiniz. Lütfen “Gereğince dikkate aldım” seçeneğiyle tüm çerezlerin kullanılmasını onaylayın ve hemen devam edin.

16 yaşından büyük müsünüz? O halde "Kabul ediyorum" diyerek çerez kullanımını onaylayın ve işlemlerinize devam edin.

Çerez ayarlarınızı seçin

Teknik ve işlevsel çerezler sitemizi ziyaret ettiğinizde her şeyin çalışması için gereklidir.
Pazarlama çerezleri ile sayfalarımız sizi tanır ve kampanyalarımızın başarısını ölçebiliriz.

JBL’den ANLIK bildirimler

ANLIK bildirimler nedir? Web bildirimleri W3C standardının bir parçası olarak tarayıcı bildirimleri üzerinden kullanıcının masaüstüne ve/veya mobil cihazına gönderilen son kullanıcı bildirimleri için bir API tanımlar. Bildirimler uçbirim cihazlarda son kullanıcının cihaza yüklü uygulamalardan tanıdığı şekliyle görünür (örn. e-postalar). Bildirimler uçbirim cihazlarda son kullanıcının cihaza yüklü uygulamalardan tanıdığı şekliyle görünür (örn. e-postalar).

Bu bildirimler, bir web sitesi operatörünün kullanıcılarının tarayıcısı açık olduğu sürece - kullanıcının o anda web sitesini ziyaret edip etmediğine bakılmaksızın- onlarla iletişim kurmasını sağlar.

Web push bildirimleri gönderebilmek için yalnızca web push kodu yüklü bir web sitesine ihtiyaç vardır. Bu, uygulaması olmayan markaların da push bildirimlerin (tam olarak doğru anda kişiselleştirilmiş, gerçek zamanlı iletişim) birçok avantajından yararlanmasına olanak sağlar.

Web bilgilendirmeleri W3C standardının bir parçası olup, son kullanıcı bildirimleri için bir API tanımlarlar. Bir bildirim kullanıcının bir web sitesinin bağlamı dışındaki bir olaydan, örneğin yeni bir blog yazısından haberdar olmasına olanak verir.

Etkinleştirilmesi ve devre dışı bırakılması son derece kolay olan bu hizmet JBL GmbH & Co. KG tarafından ücretsiz olarak sağlanmaktadır.