How do I clean the LED light bar?
Please disconnect the mains plug of the driver (power supply) for all maintenance work!
Do not use any hard items or aggressive cleaning agents for cleaning. Remove any limescale from the bottom of the light with a JBL WishWash cloth, moistened with JBL Clean A, once a week. If required, remove dust and other deposits from the top of the light with a lint-free dry cloth.
Do I need the acclimatisation mode at all?
We recommend you use the acclimatisation mode after switching to the JBL LED SOLAR technology. This applies in particular if you switch from a conventional T8/T5 tube technology or a very weak LED to this system. In contrast to many other systems, a JBL LED NATURE is sufficient to provide your entire aquarium with sufficient light and to encourage even demanding plants to grow vigorously. In short: it’s powerful! No matter which theme aquarium you’re using, you need to select the acclimatisation mode at the beginning, as this will make it easy for your plants to adjust from their previous illumination with fluorescent tubes to the much brighter light of the LED without any problems. Of course, any program can also be selected without acclimatisation.
What happens if my LED light falls into the water?
The IP67 protection class ensures that you can even use the LED with closed covers and high humidity without damaging the luminaire. However, it must never be operated directly under water.
Its protection class states that the luminaire is dustproof and protected during a temporary submersion. However, this does not mean that the LED may be operated submerged! You will also find a note on this in the manual. Should the LED accidentally fall into the water and be submerged, the IP67 protection class will serve as a protection for your personal safety against electrical accidents. In such cases, please unplug all the mains plugs first - do not reach for the LED immediately - and only then remove the device.
As long as the LED light is on, there is no problem with moisture under water. The resulting heat provides additional protection. If the lighting is switched off and cooled down, condensation can still form on the inside, as if glasses were fogging up. Please therefore install the LED light at a distance of at least 15mm from the highest water level. After an accidental submersion, you will need to have your LED inspected by the JBL Customer Service Team at the factory.
Which LED length fits my aquarium?
You will find a tabular overview on the packaging of every LED. This will tell you which LED SOLAR fits your aquarium. There are two application scenarios for this.
1. You replace an existing T5/T8 tube to install the LED as a retrofit. In this case please refer to the relevant column. Most aquarium owners prefer the shorter model because of the small distances left and right of the tube socket in the aquarium cover. You can either select according to the length of the tube (in mm) or according to the wattage.
2. The second type of installation is as a top assembly or hanging installation. Here the maximum aquarium width is decisive. Please refer to the relevant column. For this type of installation, always choose the larger of the two options for optimal illumination.
Why are there several T5 adapters in the package?
While you may have thought that all 24 W T5 tubes have the same length, there are in fact many different lengths with the same wattage on the market.That's why we've included two different adapters to facilitate a safe and easy installation. In case of an unsuccessful installation attempt, please try an alternative adapter from the box.
Why can you find two sets of wattage data on the packaging?
Decisive for you is the overall performance of a system. This determines the "power consumption" on your household bill. All manufacturers are obliged to state this amount on their packaging. This is the sum of the entire electrical consumption of a product. With the JBL LED SOLAR you have the LED and the driver (power supply) consuming electricity. Due to the reactive power and transformation processes every individual power supply consumes small amounts of power. For you as an aquarist the LED performance is crucial for your aquarium and the plants, which is why we do not want to deprive you of this information with the surprisingly low overall values.
Can I operate an LED SOLAR EFFECT unit on its own?
The operation of the LED SOLAR EFFECT on its own does not provide the lighting, which is absolutely necessary for fish and plants, in sufficient quantities. Due to the existing plug configuration, which has been selected for your safety, the LED SOLAR EFFECT must be operated together with a LED SOLAR NATUR. If you individually purchase the LED SOLAR EFFECT which is intended only as a supplement to the LED SOLAR NATUR, you will not have all the necessary accessories. This is why you only find the driver (power supply), the IR receiver and the remote control in the box of SOLAR LED NATURE. And that’s why the LED SOLAR EFFECT can only be operated in combination with the LED SOLAR NATUR.
What does “retrofit“ mean?
Retrofit refers to the option of converting conventional T5/T8 tubes to the JBL LED SOLAR system. You can, without having to remove the aquarium cover or make any structural changes, simply "plug" the new LED into the old tube sockets for operation. Many cat owners are unable to operate an "open" aquarium and therefore need an aquarium cover. The aquarium surroundings also sometimes prevent an open installation. In such cases the retrofit installation is ideal.
Can I combine two LED SOLAR EFFECT units with one LED SOLAR NATUR?
Unfortunately this is not possible. The LED SOLAR EFFECT is connected to the driver (power supply) of the LED SOLAR NATUR via the included cable switch. Thus, all the slots are already occupied. You’ll need another driver for this. You can connect one NATURE and one EFFECT to one driver. Two LED SOLAR EFFECT units on one driver are not possible due to the connectors and the maximum power consumption of the power supply.
Can the LED SOLAR be placed directly on a glass brace?
LEDs produce heat, which the metal heat sink on the back of the JBL LED SOLAR dissipates. In order to avoid unwanted discoloration on the protective glass, uneven illumination in the aquarium and heat problems on the LED, the LED SOLAR NATUR and EFFECT units should always be mounted at a distance of min. 1 cm to the material below (e.g. a glass brace). The brackets enclosed for installing them as a top assembly or the wire suspension mean that no direct contact is necessary. Installing a retrofit in the tube socket is likewise safe.
Can I connect two LED SOLAR NATUR units to just one power supply?
Unfortunately this is not possible - you will need two power supplies. One driver (power supply) has the capacity to connect one LED SOLAR NATUR and one LED SOLAR EFFECT, which together create an efficient and ideal aquarium lighting. If you need a high power light aquarium and have a particularly large number of plants, you can easily install another LED SOLAR NATUR with another driver, which is included with each LED SOLAR NATUR kit free of charge. The power supply cannot handle the power of two LED SOLAR NATUR units. Therefore, we strongly advise against the use of a home-made adapter.
How much lumen does my LED SOLAR NATURE have?
On the back of your packaging and in the instructions for use you will find a table that shows the lumen specification (at 4000 K) per product type. Unlike other LED types, the LED SOLAR NATUR mixes the light of cold white and warm white LED to produce the three possible Kelvin numbers. Maximum flexibility for your aquarium type. None of the LEDs runs at the maximum power of 100 %, thus ensuring a long lifetime. This makes it possible to generate lumen values that are almost always identical. The deviation between the 3 colour spaces is minimal.
Can I operate several LED SOLAR units with one remote control?
You can operate several IR receivers with one remote control. In doing so, the IR receiver needs to be mounted near or at the aquarium cabinet so that it can be reached unimpeded by the IR signals of the remote control. All remote controls work with the same wavelength. This enables you to operate all the receivers with just one remote control unit.
How can the LEDSOLAR NATUR and EFFECT be installed?
There are only three ways to attach the JBL LED SOLAR NATUR and EFFECT units to an aquarium and none of these involve “simply” placing the LED on it.
1. Retrofitting: using the enclosed adapters, you fit them at both ends of the LED body and put it into the old tube sockets (T5/T8).
2. Top assembly: with the enclosed brackets, the LEDs can be safely positioned on the edge of the aquarium, without any danger of them falling in or being too close to the water surface.
3. Suspension: Using the LED SOLAR Hanging accessory, you can position your LED down hanging from the ceiling so that it hovers above the aquarium.