In unserem FAQ‑Bereich findet ihr Antworten auf die am häufigsten gestellten Fragen. Solltet ihr hier nicht fündig werden, zögert bitte nicht, uns direkt zu kontaktieren – wir helfen euch gerne weiter.
When you adjust the working pressure, the CO2 addition needs to be running actively, otherwise the change will not be immediately visible in the event of a reduction. An increase is also visible without running CO2, but not immediately. That’s why you need to ensure that CO2 is added during the adjustment process for every reduction or increase.
Please note two important points: _x000D_ _x000D_ 1) Cylinder: Reusable cylinders are TÜV tested and this is stamped on the cylinder. This test needs to be renewed every 10 years, with the bottom of the cylinder and the valve sealing and threaded joint being tested. _x000D_ _x000D_ 2) The carbon dioxide: _x000D_ Depending on its concentration, carbon dioxide is harmful in the air. _x000D_ The respiratory rate and pulse rate increase at a carbon dioxide concentration of 3-5%. Other symptoms are headaches, discomfort and ringing in the ears. Carbon dioxide concentrations of 8-10% and more cause these symptoms to become more pronounced. This may lead to cramps, fainting, apnoea and death from suffocation. _x000D_ _x000D_ One 500 g cylinder contains 500 g CO2. This is equal to 11.36 mol (chemical substance amount unit). One mol of a gaseous substance has a volume of 22.414 l under normal conditions (273.15 K, 101325 Pa), so that 500 g of CO2 result in a volume of 254.7 l. CO2 is heavier than air, so that it collects on the ground. This corresponds to a CO2 height level in the range of 12.735 mm = 1.27 cm for a room of 20 m². If it is mixed completely with the air in a room of 20 m² and a height of 2.5 m (corresponds to 50,000 l), this corresponds to a maximum gas concentration of 0.5 volume %, which is well below the dangerous level._x000D_
True to the motto, better safe than sorry, some aquarists install several check valves in the same circuit. For example, if you use the JBL PROFLORA direct inline diffuser or the JBL PROFLORA CO2 Count Safe bubble counter, you already have an integrated check valve. If you also use a separate check valve (JBL PROFLORA SafeStop), there may be problems with the opening of the check valves. This effect can be observed if, after the night switch-off or interruption of the supply with the controller, the addition does not restart automatically. Please note that, depending on the working pressure and the number of bubbles, a few minutes may pass between the start of the supply and the visible entry of CO2 into the aquarium. _x000D_ Each spring in a check valve needs a certain pressure to be opened. Several springs can therefore interfere with each other and, depending on the distance between the two check valves, reduce the pressure at the spring to such an extent that it remains closed. Therefore, please always use only one check valve for your CO2 installation.
Yes, the JBL PROFLORA CO2 products are designed exclusively for use in the aquarium. The gas contained promotes plant growth and works with fine precision so that even the smallest quantities can be supplied to the aquarium. Constant operation and the safety of the fish are thus guaranteed.
Your system is probably still under pressure. Close the cylinder valve and remove the CO2 hose from the pressure regulator fitting. Open the regulating screw and release the pressure still present in the pressure regulator until both pressure gauges show 0 bar. Loosen the connecting nut of the pressure regulator fitting from the cylinder valve.
For a long time JBL CO2 pressure reducers had a preset working pressure of 1.5 bar. This has become established in people's minds. With the new JBL PROFLORA CO2 pressure reducers with pressure gauges, the working pressure is set to 0 bar on delivery. You admit CO2 via the large adjustment knob for the working pressure and turn it until the desired working pressure is reached. Approx. 1.2 bar is the maximum setting here. A minimum of 0.6 bar is required for the operation of all JBL non-return valves or backflow protections. This ensures that the check valve opens. A higher working pressure is not necessary, which is why all the accessories also work with the JBL PROFLORA BIO SETs. A lot of CO2 accessories available on the market give very different specifications for the working pressure. To be on the safe side, the standard of 1.5 bar which is common on the market is mentioned. As a rule, the working pressure required is the same as that on which the JBL PROFLORA CO2 accessories are based. Only a few exceptions require a working pressure of over 2 bar and are very special technical components.
No, a tool should never be used. The use of a tool can lead to damage. There is a thin spike at the tip of the needle valve. If the needle valve is closed clockwise and turned too tightly or with a tool, it may break off and damage the pressure regulator._x000D_ _x000D_
No, a tool is not required and should not be used under any circumstances. The use of a tool can lead to damage. You can mount the pressure reducer on the CO2 cylinder with your hands. Turn only until you feel resistance and then turn about half a turn more. This way the pressure regulator fitting is hand-tight. A short hissing sound will be heard when attaching the fitting to disposable cylinders.
Stelle deine Frage an das JBL Service Team.