Heat and temperature in terrariums

Since no terrarium animal can produce its own heat (cold-blooded animals), they depend on the ambient temperature. Many lizards and snakes actively seek out places where they can warm themselves in the temperature of the ground or the sun. Only with the right body temperature are they capable of reaching their peak performance (hunting) and keeping their metabolism working normally.

Because the sun generates heat in the wild, light is associated with heat. That’s why a lot of terrarium animals seek out places under bright spotlights. They would not recognize a dark (infrared) ceramic heat lamp without visible light! The Ceramic heat lamp is an ideal way to supply heat to the terrarium during the dark phase. Ceramic heat lamps and heating mats are the only way to heat without light.

When the animals have warmed up, they start looking for cooler places again. That’s why terrariums must never be heated evenly, but need different temperature zones. A floor heating like JBL TerraTemp heatmat should for example only be attached under one area of the terrarium.

It is also important that different daytime and nighttime temperatures are maintained, recreating the animals’ habitat conditions. Especially in deserts, it can be very cold at night and the animals retire to caves where heat is stored by the surrounding sand or rock. But even in rainforests the heat is not always on the same level. In the Amazonian lowlands, for example, the night temperature can drop to 22 ° C in the early morning hours!

Heating in a terrarium should be dimensioned so that the animals will not be “roasted” in the event that the control technology fails. In other words, a small terrarium should not be equipped with an oversized 100 watt heating cable with a controller. Instead it should have a small floor heating of 8 to 15 W ( JBL TerraTemp heatmat ). The heating effect of the lighting also needs to be taken into account. As a result, when the lighting is turned off, the nighttime drop in temperature occurs simultaneously.

The heat dissipation of a terrarium can be reduced – and savings in energy costs achieved as a result – by insulating the side panes with insulating material on the outside to prevent heat loss. Foam pads such as the JBL AquaPad under the bottom panel prevent heat emission but also prevent the bottom panel from bursting in case the supporting surface is uneven and there is no heating mat attached outside on the bottom. When placing a heat mat there, though, it is imperative to follow the relevant instructions in order to ensure a sufficient rear ventilation of the heating mat. The JBL floor heating mats ( JBL TerraTemp heatmat ) come with “feet” as spacers. If the lighting is not sufficient for heating and the installation of a heating mat under the terrarium is not possible, use ceramic heat emitters, such as JBL ReptilHeat ). These ceramic heaters heat up (not visible from the outside) and release the heat into the terrarium air. To prevent animals from getting burned, they should always be covert with a heat protection basket ( JBL TempSet Heat ).

Heat requirement of terrarium animals

In the following section you will find information about the heat requirements of animals from various habitats

Heat for tropical forest animals

Tropical forest dwellers usually need high daytime and slightly lower nighttime temperatures (e.g. Amazonia 32 °C day/23 °C night – should not fall below this limit!). You can lower temperatures by switching off the warm daytime lighting at night.

Heat for animals that are active at dusk and at night

Nocturnal tropical forest animals require higher temperatures between 23 and 30 °C during the night, whereas night-active desert animals prefer lower temperatures from 15-22 °C.

Heat for desert animals

Desert animals are used to high daytime and often to low nighttime temperatures. If it gets too warm for them during the day, they need to be able to retire to cooler places in the terrarium.

Hinweise und Einwilligung zu Cookies & Drittinhalten

Wir verwenden technisch notwendige Cookies/Tools um diesen Dienst anzubieten, zu betreiben und abzusichern. Des Weiteren verwenden wir mit Deiner ausdrücklichen Einwilligung Cookies/Tools zum Marketing, Tracking, Erstellen personalisierter Inhalte auf Drittseiten sowie zur Darstellung von Drittinhalten auf unserer Webseite. Eine von Dir erteilte Einwilligung, kannst Du jederzeit mit Wirkung für die Zukunft über den Menüpunkt „Cookie-Einstellungen“ widerrufen.
Mit dem Klick auf „Alle erlauben“ erteilst Du uns die ausdrückliche Einwilligung zur Verwendung von Cookies/Tools um die Qualität und Performance unseres Dienstes zu verbessern, zur funktionalen und personalisierten Leistungsoptimierung, die Effektivität unserer Anzeigen oder Kampagnen zu messen, für personalisierte Inhalte zu Marketingzwecken, auch außerhalb unserer Webseite. Dies ermöglicht uns personalisierte Online-Anzeigen und erweiterte Analysemöglichkeiten über Dein Nutzerverhalten. Dies beinhaltet auch den Zugriff und die Speicherung von Daten auf Deinem Gerät. Deine Einwilligung kannst Du jederzeit mit Wirkung für die Zukunft über den Menüpunkt „Cookie-Einstellungen“ widerrufen.
Über die Schaltfläche „Einstellungen ändern“ kannst Du individuelle Einwilligungen zu den Cookies/Tools erteilen, widerrufen und erhältst weitergehende Informationen zu den von uns eingesetzten Cookies/Tools, deren Zwecke und Laufzeiten.
Mit dem Klick auf „Nur unbedingt erforderlich“ werden nur technisch notwendige Cookies/Tools eingesetzt.

Our data protection declaration tells you how we process personal data and what purposes we use the data processing for.

PUSH messages from JBL

What are PUSH messages? As part of the W3C standard, web notifications define an API for end-user notifications that are sent to the user's desktop and/or mobile devices via the browser. Notifications appear on the end devices as they are familiar to the end user from apps installed on the device (e.g. emails). Notifications appear on the end user’s device, just like an app (e.g. for emails) installed on the device.

These notifications enable a website operator to contact its users whenever they have a browser open - it doesn’t matter whether the user is currently visiting the website or not.

To be able to send web push notifications, all you need is a website with a web push code installed. This allows brands without apps to take advantage of many of the benefits of push notifications (personalised real-time communications at just the right moment).

Web notifications are part of the W3C standard and define an API for end user notifications. A notification makes it possible to inform the user about an event, such as a new blog post, outside the context of a website.

JBL GmbH & Co. KG provides this service free of charge, and it is easy to activate or deactivate.